Woodstock W1675 Instrukcja Użytkownika

INSTRUCTION MANUALMODEL W167513" Portable PlanerPhone: 1-360-734-3482 • On-Line Technical Support: [email protected] © NOVEMBER

SAFETY-8-110V OperationELECTRICALUsing extension cords with an undersized gaugeor one that is too long, generates heat in thecord that may cause fire

ASSEMBLY-9-Layout and inventory the parts shipped withyour Planer. See Figure 6. This will help withmachine assembly. Planer Unit 1Handwheel 1Magnets

ASSEMBLY-10-BeginningAlthough the main components of the SHOPFOX®W1675 are assembled at the factory,some assembly is required. The following seriesof

ASSEMBLY-11-Planer BaseMountingSurfaceFigure 9. Hardware mounting assembly.MountingFor proper results and safe use, the ModelW1675 must be mounted to

Figure 11. Handwheel mounted to the shaft.Figure 12. Dust port mounted to planer.ASSEMBLY-12-Handwheel HandleTo mount the handwheel to the planer doth

ADJUSTMENTS-13-ADJUSTMENTSControlsFamiliarize yourself with the controls of yournew planer. They will be frequently mentionedthroughout the instructio

ADJUSTMENTS-14-Turning/ChangingKnivesThe Model W1675 features a 2 knife, quickchange cutterhead system with double-sided,disposable knives. The knives

ADJUSTMENTS-15-Figure 18. Remove six screws from the knife binder.Figure 19. Lift out the locking plate with themagnets.5. Use the T-handle Allen®wren

ADJUSTMENTS-16-Figure 21. Position the magnets and blade taper.Figure 22. Position the knife on the cutterhead.Figure 23. Push the cutterhead lock lev

ADJUSTMENTS-17-Extension TablesThe extension tables have been set at thefactory and require no adjustments upon initialoperation. However, over the li

WARNINGSome dust created by power sanding, sawing,grinding, drilling, and other construction activitiescontains chemicals known to the State of Califo

OPERATIONS-18-OPERATIONSStarting the PlanerOnce assembly is complete and adjustmentshave been made, the machine is ready for a testrun. The purpose of

OPERATIONS-19-Figure 30. Face joint the concave side of cuppedstock before planing.Figure 29. Only plane clean stock.Basic OperationsDO NOT operate th

OPERATIONS-20-3. Support the ends of the wood and turn theplaner on.4. Keeping your hands clear of the cutterhead,slowly and evenly push the wood into

OPERATIONS-21-TroubleshootingPlaning ResultsFUZZY GRAIN — Grain fibers stand up on theworkpiece after planing. SOLUTIONS:• Do not surface damp or wet

MAINTENANCE-22-LubricationSince all bearings are shielded and permanentlylubricated, simply leave them alone until theyneed to be replaced. Do not lub

-23-The following pages contain parts diagrams/listsand a warranty card for your SHOP FOX®ModelW1675.If you need parts or help in assembling yourmachi

PARTS-24-

PARTS-25-REF PART # DESCRIPTION REF PART # DESCRIPTION1 X1675001 LEFT COVER2 XPSB11M CAP SCREW M8-1.25 X 163 X1675003 BUSHING4 XPS38M PHLP HD SCR M4-0

251061167741081311024499100105107110134132117116121120119118101115114719112103104111761131212810113142102441223029784796989089978525133137PARTS-26-

123 X1675123 TOOLING TRAY124 X1675124 “T” ALLEN WRENCH 4MM125 X1675125 KNIFE SETTING GAUGE126 XPTLW02M EXT-TOOTH WASHER 5MM127 X1675127 SPRING128 X167

PAGEINTRODUCTION ...2About Your New Planer ...

-28-YOUR NOTES

-29-YOUR NOTES

-30-YOUR NOTES

CUT ALONG DOTTED LINE10. What stationary woodworking tools do you own? Check all that apply.___Air Compressor ___Panel Saw___Band Saw ___Planer___Dril

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWOODSTOCK INTERNATIONAL, INC.P.O. BOX 2309BELLINGHAM, WA 98227-2309

INTRODUCTION-2-INTRODUCTIONAbout Your New PlanerYour new SHOP FOX®Planer has been specially designed to provide many years of trouble-free service.Clo

INTRODUCTION-3-Warranty and ReturnsWoodstock International, Inc. warrants all SHOP FOX®machinery to be free of defects fromworkmanship and materials f

SAFETY-4-READ MANUAL BEFORE OPERATING MACHINE.FAILURE TO FOLLOW INSTRUCTIONS BELOW WILLRESULT IN PERSONAL INJURY.SAFETY FIRST!Standard Safety Instruct

SAFETY-5-12. Do not force tool. The machine will do a safer and better job at the rate for which it was designed.13. Use correct tool. Do not force ma

SAFETY-6-ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERSUse this and other machinery with cautionand respect and always consider safetyfirst, as it applies

SAFETY-7-Figure 1. DO NOT place hands inside planerwhen operating.Figure 2. Feed wood by hand only until planerfeed roller begins to pull wood inside