Woodstock REBEL W2000 Instrukcja Użytkownika

COPYRIGHT © 1995 BY WOODSTOCK INTERNATIONAL, INC., REG.# TX 3 360-515 WWAARRNNIINNGG:: NNOO PPOORRTTIIOONN OOFF TTHHIISS MMAANNUUAALL MMAAYY BB

W2000 Rebel® – 9Although the power switch on your router can beturned on and off each time you use The Rebel®, theoptional switch (Item Number W2001)

10 – W2000 Rebel®If using the optional safety switch, make sure it is inthe off position. You can now plug your router into thecord connected to the b

W2000 Rebel® – 11AA.. RRoouutteerr TTaabbllee IInnsseerrttLocated in the four corners of the insert ledge on thetable are four holes. These holes

12 – W2000 Rebel®For applications where the entire edge of the work-piece is being shaped, the outfeed fence must be offsetby the same amount of mater

W2000 Rebel® – 13FFiigguurree 1188..Fence alignment.FFiigguurree 1199.. Safety guard adjusted properly.For applications where an adequate bearing

14 – W2000 Rebel®FFiigguurree 2200..Miter gauge.SStteepp 66- Adjust the 90° miter gauge stop bolt so it restsagainst the pin. Re-tighten the jam nu

W2000 Rebel® – 15AA.. SSiittee PPllaannnniinngg BB.. WWoorrkkiinngg HHeeiigghhttAlthough The Rebel®is completely portable and canbe set up and us

16 – W2000 Rebel®DD.. GGeenneerraall OOppeerraattiioonnssThe general operating procedures are just that: “gener-al in nature”. They are not the fina

W2000 Rebel® – 17EE.. SSttrraaiigghhtt EEddggee SShhaappiinnggStraight edge shaping requires the use of the fenceassembly. Although many edge shap

18 – W2000 Rebel®GG.. FFrreeeehhaanndd WWoorrkkThe Rebel®is ideally suited to performing freehandwork. Freehand shaping enables you to profile the e

TTAABBLLEE OOFF CCOONNTTEENNTTSSII.. IINNTTRROODDUUCCTTIIOONN...

W2000 Rebel® – 19SStteepp 66 - Once the workpiece or fixture is contactingthe guide bearing on the router bit, move theworkpiece or fixture away fr

20 – W2000 Rebel®FFiigguurree 2288.. Stop block in position.HH.. UUssiinngg SSttoopp BBlloocckkssIf a particular application requires that you pr

W2000 Rebel® – 21Because there are no moving parts, maintenance is vir-tually eliminated. However, we do make the followingrecommendations:••Give the

22 – W2000 Rebel®VVII.. PPaarrttss BBrreeaakkddoowwnn

W2000 Rebel® – 23VVIIII.. PPaarrttss LLiisstt1 TABLE TOP2 LEG3 PANEL4 SIDE PANEL5 CAP SCREW 1/4"-28 X 5/8''7 SETSCREW 10-32 X 5/8&ap

24 – W2000 Rebel®Woodstock International, Inc. (Woodstock) warrantsthis product against defects in workmanship and mate-rials under normal use and ser

2– W2000 Rebel®FFoorr YYoouurr OOwwnn SSaaffeettyy,, RReeaadd IInnssttrruuccttiioonnss BBeeffoorree UUssiinngg TThhee RReebbeell®®AA.. SSaaff

W2000 Rebel® – 3BB.. AAddddiittiioonnaall SSaaffeettyy RRuulleess FFoorr TThhee RReebbeell®®1188.. NNEEVVEERR LLEEAAVVEE TTHHEE TTOOOOLL

4– W2000 Rebel®Woodstock International, Inc. is proud to offer theW2000 Rebel®Router Table. The Rebel®, namedbecause of its radical design and constru

W2000 Rebel® – 5The Rebel®is designed for heavy-duty use, yet itweighs only 35 pounds and is completely portable.However, when lifting, we must cauti

6– W2000 Rebel®Assembly of The Rebel® is extremely straight forwardand can be accomplished with just a few simple handtools. In fact, the only tools y

W2000 Rebel® – 7FFiigguurree 44..Attaching the fence.The Rebel®has a two-part, split fence designed foreither straight-line or offset shaping. Assem

8– W2000 Rebel®The safety guard system consists of a clear plasticguard and arm which have been assembled at the fac-tory. There is also a height adju